Turning junk mainly, magazines, calendars and brochures into decors is a very great project. Before throwing away your junk papers, you might consider recycling them into something useful. Below are some steps on how to make paper beads out of your favorite colored pieces of paper.
First, measure the size of the piece you want to cut using a ruler while marking it with a pen. Cut along the lines you have marked using a pair of scissors. The width and outline of the cut strips will determine the end results. Use a template as a guide when cutting the strips. The utmost rims are important in designing because they are the ones which are noticeable.
Secondly, take a strip and roll it onto itself from the wide end using a toothpick or dowel. This forms a cylindrical shape. When you are through with the alignment, roll the piece back and apply some glue across the breadth using a hairbrush. To ensure the symmetry of the bead is achieved, roll the paper over the glue and make sure at each side the spirals are equal. If you want a freestyle design, you should not trouble over alignment and you can then let the strip be a bit off the center.
Thirdly, roll tightly the triangle onto the dowel. Make certain that the strip is rolled and stuck down before rolling it on your finger. To ensure that it is protected and cylindrical, put a little pressure on it. If it unravels, put on some more glue and hold it still until the glue is set. Several layers of glue can be applied so as to protect your work.
Next, put your bead on a string in the size you require. Apply varnish to seal the outside of your beads using a brush and leave them to dry out. This assists in hardening and making them water resistant. It is wise to twist them around the bamboo skewer so that they do not stick when they are fully dry. Use foam or a cushion to hold up the rolling tube and stop the excess glue from spreading. Numerous coats are added to ensure the finish lasts longer and is glossy.
You can then remove the beads after a few hours. This is when your varnish has positioned on your bead. It can also be done by sliding the items out of a bamboo skewer or dowel. It will hold only if it is glued and wrapped fine. If you experience unraveling of the bead, add more glue.
Crafting more beads will complete the project. You can add some paint to bring out your designs and put some glitters on the blobs convey the sparkly form. Tie the beads in a string and not a thread. Make decorating patterns with the string along the outer surface of a paper. For geometric and spiral patterns, use a little wire to align the beads. A little glaze might be added using nail polish or paint for coating.
Going green by using old papers is both fun and a way of conserving the environment. It is an inexpensive project which many people enjoy doing and make good things out of it including gifts.
First, measure the size of the piece you want to cut using a ruler while marking it with a pen. Cut along the lines you have marked using a pair of scissors. The width and outline of the cut strips will determine the end results. Use a template as a guide when cutting the strips. The utmost rims are important in designing because they are the ones which are noticeable.
Secondly, take a strip and roll it onto itself from the wide end using a toothpick or dowel. This forms a cylindrical shape. When you are through with the alignment, roll the piece back and apply some glue across the breadth using a hairbrush. To ensure the symmetry of the bead is achieved, roll the paper over the glue and make sure at each side the spirals are equal. If you want a freestyle design, you should not trouble over alignment and you can then let the strip be a bit off the center.
Thirdly, roll tightly the triangle onto the dowel. Make certain that the strip is rolled and stuck down before rolling it on your finger. To ensure that it is protected and cylindrical, put a little pressure on it. If it unravels, put on some more glue and hold it still until the glue is set. Several layers of glue can be applied so as to protect your work.
Next, put your bead on a string in the size you require. Apply varnish to seal the outside of your beads using a brush and leave them to dry out. This assists in hardening and making them water resistant. It is wise to twist them around the bamboo skewer so that they do not stick when they are fully dry. Use foam or a cushion to hold up the rolling tube and stop the excess glue from spreading. Numerous coats are added to ensure the finish lasts longer and is glossy.
You can then remove the beads after a few hours. This is when your varnish has positioned on your bead. It can also be done by sliding the items out of a bamboo skewer or dowel. It will hold only if it is glued and wrapped fine. If you experience unraveling of the bead, add more glue.
Crafting more beads will complete the project. You can add some paint to bring out your designs and put some glitters on the blobs convey the sparkly form. Tie the beads in a string and not a thread. Make decorating patterns with the string along the outer surface of a paper. For geometric and spiral patterns, use a little wire to align the beads. A little glaze might be added using nail polish or paint for coating.
Going green by using old papers is both fun and a way of conserving the environment. It is an inexpensive project which many people enjoy doing and make good things out of it including gifts.
About the Author:
Learn how to make paper beads by following the instructions we have provided online. The website that reveals the tips can be found at http://www.paperbeadgirl.com.
No comments:
Post a Comment